{"id":903,"date":"2010-09-02T17:11:20","date_gmt":"2010-09-02T17:11:20","guid":{"rendered":""},"modified":"2017-12-06T05:11:13","modified_gmt":"2017-12-06T05:11:13","slug":"made-the-big-cut","status":"publish","type":"post","link":"http:\/\/jasonbeaver.com\/rv7\/2010\/09\/02\/made-the-big-cut\/","title":{"rendered":"Made the Big Cut"},"content":{"rendered":"

I came out to the garage this morning and made the big cut. \u00a0A lot of builders seem to get all worked up about this, but it’s a total non-event. \u00a0Just go for it. \u00a0The canopy in this section is significantly thinner than around the edges (just over 1\/8″ thick), so it cuts fast. \u00a0The whole cut took only 2-3 minutes.<\/p>\n

<\/a><\/center>I smoothed out the edge and fit the canopy temporarily on the fuselage. \u00a0Blurry, but this looks sweet! \u00a0There’s still pretty of trimming left to go though.<\/p>\n

<\/a><\/center>I also edge finished the aft window. \u00a0This will be put aside for the time being while I work on the forward canopy.<\/p>\n

<\/a><\/center>With the top center of the aft edge of the canopy flush with the line, the sides are forward of the line by nearly 1\/4″. \u00a0This was expected though since there was a gap at the top before the big cut. \u00a0The canopy pivoted down around the front edge. \u00a0I still have to lower the canopy more in the front though, so this will be reduced somewhat. \u00a0After the front is at the proper height, I’ll remark the line and trim the aft edge to follow the line perfectly.<\/p>\n

<\/a><\/center>I’m planning on using sikaflex adhesive around the canopy channel and cabin frame, so I taped some 1\/8″ thick pieces of rubber to both pieces. \u00a0This will raise the canopy enough for the adhesive to fit.<\/p>\n

<\/a><\/center>After clamping the canopy in place, I marked a further trim line around the front that will finally remove the last of the flare where the front flange used to be. \u00a0I also marked a cut line along the side that will bring them up to within 1\/2″ of their final position. \u00a0These cuts need to be done to get the canopy to transition more smoothly to the sides. \u00a0I’ll try to do these before work tomorrow.<\/p>\n

<\/a><\/center><\/p>\n","protected":false},"excerpt":{"rendered":"

I came out to the garage this morning and made the big cut. \u00a0A lot of builders seem to get all worked up about this, but it’s a total non-event. \u00a0Just go for it. \u00a0The canopy in this section is significantly thinner than around the edges (just over 1\/8″ thick), so it cuts fast. \u00a0The … Read More<\/a><\/p>\n","protected":false},"author":1,"featured_media":0,"comment_status":"open","ping_status":"open","sticky":false,"template":"","format":"standard","meta":{"footnotes":""},"categories":[6],"tags":[],"class_list":["post-903","post","type-post","status-publish","format-standard","hentry","category-finishing"],"_links":{"self":[{"href":"http:\/\/jasonbeaver.com\/rv7\/wp-json\/wp\/v2\/posts\/903","targetHints":{"allow":["GET"]}}],"collection":[{"href":"http:\/\/jasonbeaver.com\/rv7\/wp-json\/wp\/v2\/posts"}],"about":[{"href":"http:\/\/jasonbeaver.com\/rv7\/wp-json\/wp\/v2\/types\/post"}],"author":[{"embeddable":true,"href":"http:\/\/jasonbeaver.com\/rv7\/wp-json\/wp\/v2\/users\/1"}],"replies":[{"embeddable":true,"href":"http:\/\/jasonbeaver.com\/rv7\/wp-json\/wp\/v2\/comments?post=903"}],"version-history":[{"count":2,"href":"http:\/\/jasonbeaver.com\/rv7\/wp-json\/wp\/v2\/posts\/903\/revisions"}],"predecessor-version":[{"id":3010,"href":"http:\/\/jasonbeaver.com\/rv7\/wp-json\/wp\/v2\/posts\/903\/revisions\/3010"}],"wp:attachment":[{"href":"http:\/\/jasonbeaver.com\/rv7\/wp-json\/wp\/v2\/media?parent=903"}],"wp:term":[{"taxonomy":"category","embeddable":true,"href":"http:\/\/jasonbeaver.com\/rv7\/wp-json\/wp\/v2\/categories?post=903"},{"taxonomy":"post_tag","embeddable":true,"href":"http:\/\/jasonbeaver.com\/rv7\/wp-json\/wp\/v2\/tags?post=903"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}